Water Repellent – repel water due to hydrophobic “skin” effect.
Our coatings and impregnations have a “high contact angle” which means that droplets of water roll very easily over the surface, taking contaminants with them.
The higher the contact angle, the lower the surface area of the droplet in contact with the treated surface, rather like the difference between a ball bearing and a bean bag on a sheet of glass.
Scrupulously Clean Surfaces
At the microscopic level, treated surfaces are so smooth that they are easily cleaned – usually with just water – but also with solvents and other cleaners in the case of our Anti Graffiti products
Surface is so smooth that dirt and other particles find it difficult to stick depriving bacteria of food. Hence anti-microbial properties without the inclusion of biocides.
Ultra-thin coating
A little goes a very, very long way!
Coatings follow the contours of a surface, meaning that they will not make non-slip surfaces slippery.
Coatings are extremely flexible, will not crack on flexible surfaces.
Breathing characteristic: Allow moisture – water as vapour – to pass through due to tiny gaps between nano-particles.
Will not (usually) change the appearance of a surface. (We have some products such as Nanolia Protect that are designed to enhance surface gloss and deepen colour.)
Environmentally friendly
Non toxic, neither carcinogenic nor mutagenic
Easy to apply with short drying times and no noxious fumes
Long working life and then easily re-applied
Specific Product Properties
Powercoat PRO – for wood, stone, metals and some plastics
Excellent gloss and long-life properties
Long lasting “easy-to-clean” final coating
Old and bleached surfaces “freshened up” as new
Protection against UV rays prevents bleaching of surfaces
“Anti-Graffiti” and “Anti-fingerprinting” finish
Long lasting protection against corrosion.
Abrasion resistant
Stability against condensation and climatic/temperature variations
Resistance against acid and solvent attack
No special preparation of the base material required
High productivity because of extremely thin minimum layer thickness
Wood Prodeck – for wood
Water-based, ideal for indoor use
No oil, no paint – no visible change to the treated material
Water and oil – even red wine- are resisted and cannot be absorbed into the wood
Reduction of soiling/dirtying of the product with cleaning also made much easier
Non-toxic and compliant with DIN EN 71 parts 3 and 9 “safety for toys”
Resistant to seawater, salt spray and acid rain
Free of silicones, waxes and oils
Retains “working-properties” for up to 3 years without any rubbing-off
High coating efficiency due to the very thin required coating application
Glass Clear – for glass and ceramics
Water, dust and dirt simply pearl-off.
“Easy-to-clean” effect.
Soiling is washed off without the use of commercial cleaning products.
Anti-graffiti effect when used on marble or granite.
No clouding of the surface or reduction of reflective properties.
Ice/frost formation can be very easily scraped off.
Insects can be easily removed.
Drastically reduced chalky deposits.
May be used indoors or outdoors.
Long-life effect.
Resistant to chemicals and solvents.
Highly efficient coating capacity, economical in amount of product required.
May be renewed at any time.
Powercoat – for plastics, wood, stone, glass and metals
Long lasting “easy-to-clean” final coating
Optically almost neutrally, no gloss
Protects against corrosion and oxidisation
Extremely water- and oil-repellent
“Anti-Graffiti” and “Anti-fingerprinting” capacity
High productivity because of extremely minimum layer thickness
Powercoat M Series – for stone and metals
Extremely good protection against corrosion
(After approx. 2,500 hours of salt-spray testing no changes in the surface were detected)
Perfect gloss and long-life properties
No previous preparation or chroming required when used on aluminium
Resistant to abrasion
High coverage due to the very thin coating required
Stone Guard – for stone and other absorbent mineral surfaces
No oil, no paint, no visible change to the treated materials
Water and oil are resisted and cannot be absorbed
Reduction of new soiling/marking – easier to clean
Non poisonous according to German Regulation DIN EN 71 Parts 3 and 9 “Safety of toys”
Resistant to acid rain and to seawater
Free from silicones, waxes and oils
Water based
High efficiency owing to thin application coating requirement
Long term working effect
Concrete Protect – for stone and other cementitious mineral surfaces
Single component, aqueous solution
Waterproofing
Prevents efflorescence and weathering as well as algae
Prevents the penetration of pollutants into the concrete
Optically neutral
Hydrophobic beading
Protection from frost, snow and ice (resistant to commonly used de-icers)
Highly abrasion resistant
Operating temperature from -30 ° C to 700°C
Increases the compressive and flexural strength of cementitious materials
Environmentally-sound – manufactured from inorganic materials
Good penetration through low viscosity
Stone Coat – for marble, stone, glass and some plastics
Single component, environmentally friendly, aqueous solution
Seals against the ingress of salt water, sewage, chemicals, fats and oils
Increases surface strength of concrete and screed
Reduces abrasion
Hydrophobic and oleophobic beading
Stain protection – proof against coffee, cola, red wine, etc …
Closes the pores and prevents the penetration of pollutants into the concrete or marble
Prevents efflorescence and weathering
Reduction of algae and moss
Protection from frost, snow and ice
Optically nearly neutral
Abrasion resistant
Excellent penetration
Textile Solvent – for fabrics and leather
Invisible
Will not discolour or “yellow”
Strong impregnation effect
Increases the lifetime of treated surfaces
Very easy to clean upholstered items
Textile Protect WB – for fabrics
Machine washable up to 10 times
Invisible
Will not discolour or “yellow”
Strong impregnation effect
Increases the lifetime of treated surfaces
And many more!