Graffiti Remover Gel PRO

  • Can be used with UNTREATED surfaces
  • Graffiti attacks can be removed without damaging the surface
  • Used on both porous and non-porous surfaces
  • Spray-Paints, Felt-tip Pens and Ink stains removed quickly
  • Leaves no residue
  • Environmental Friendly
  • Biodegradable
  • Permanent “easy-to-clean“ finish

GRAFFITI Removal Gel PRO™

Graffiti Removal Gel PRO is for use on porous and non-porous surfaces not yet protected by Nanolia’s Anti-graffiti products. It is especially suitable for the removal of graffiti, emulsion paints and latex colours and enables acrylic plaster, acrylic, alkyd, styrene and NC varnishes to be readily removed with water. Spray paints, felt-tip pen and ink stains as well as car paints and coatings are removed quickly and easily without leaving any residue. Also suitable for removing multiple coats of paint, adhesive fabric and foam carpet remnants, it can even remove tar from carpet pile without removing the colour – one of the most difficult cleaning tasks imaginable!

Environmentally friendly, Graffiti Removal Gel PRO is biodegradable, free of chlorine, hydrocarbons, strong acids or alkalis.

 

Technical Data:
Mixing proportions Ready to use
Dilution Not dilutable
Finish Deactivate with H2O
Colour Transparent
Layer thickness: N/A
Temperature range 5° – 35°C
Pot life approx. 6 hours (at 20° C)
Activation time* approx. 15 minutes (at 20° C)
Complete Action*: approx. 15 minutes (at 20° C)
Application Spray or brush or wet wipe
Spread rate on non porous surfaces: approx. 40m ² kg
*Application at ambient temperatures below 5 °C can affect outcome

 

 

Always test a small sample to ensure that the desired result is achieved before proceeding with the main project. If in doubt, do not proceed.

Use only on dry surfaces at ambient temperature between 0° C – 40°C. Brush evenly onto the surface with a soft, natural bristle brush – do NOT use plastic bristles. Leave between 20 and 30 minutes to dissolve the graffiti. Sometimes it may be necessary to apply a second coat of fresh cleaner in conjunction with a longer exposure time (max. 24 hours).

Do not allow the surface to dry out completely. Once the graffiti has been dissolved, it can be cleaned off. Usually wiping with a sponge is sufficient for non-porous surfaces, but for tougher marks and on porous surfaces it may be necessary to use a pressure washer at a maximum of 10-12 bar.

According to the type of graffiti, it may be necessary to repeat the cleaning process, using a longer exposure time up to a maximum of 24 hrs.

  • Used cleaning equipment can be washed out with water or white spirit.
  • The resulting sludge and residues should be disposed of as special waste.
  • The waste water should be disposed of in accordance with local regulations. When correctly used it will not contaminate waste water treatment plant.
The product may be stored for at least 12 months in its original packing. Do not transfer remaining content to plastic containers. Do not pour remaining content down the sink! Protect from frost and direct sunlight.
Empty containers can be disposed of with household waste. Containers with remaining contents must be disposed as hazardous waste in compliance with local regulations. Do not pour remaining content down the sink!
When using this product please take note of these instructions. We wish to make it clear that the use of chemical preparations should only take place when the safety measures are observed and always out of the reach of children.
The information in this Material Safety Data Sheet (MSDS) was obtained from sources which we believe to be reliable. However, the information is provided without any warranty, express or implied, regarding its correctness. The conditions or methods of handling, storage, use or disposal of the product are beyond our control and may be beyond our knowledge. For this and other reasons, we do not assume responsibility and expressly disclaim liability for loss, damage or expense arising out of or in any way connected with the handling, storage, use or disposal of the product. This MSDS was prepared and is to be used only for this product. If the product is used as a component in another product, this MSDS information may not be applicable.

In the event of a new version of this information becoming available – the information set out here is no longer valid.