PowerCoat

  • Long lasting “easy-to-clean” final coating
  • Optically almost neutral, no gloss
  • Protects against corrosion and oxidization
  • Highly water-resistant and oil-repellent
  • “Anti-Graffiti” and “Anti-fingerprint” performance
  • High coverage due to extremely minimum layer thickness

Nanolia Powercoat™

Perfect for use on stainless-steel, chrome, aluminium, brass, copper and previously coated surfaces Nanolia Powercoat coating is highly resistant to abrasion and chemical attack due to its long lasting molecular bond with the surface of the base material. A single-component clear coating based upon chemical nanotechnology, Nanolia Powercoat  offers an almost invisible coating for smooth, non absorbent surfaces. Sealed surfaces are easy to maintain without the need for special cleaning agents and are resistant to further soiling of the surfaces – the classic “easy-to-clean” effect. Fingerprinting and smearing are significantly reduced.

Used on metals Nanolia Powercoat offers long-life protection against corrosion. Fully-cured surfaces are also resistant to the effects of UV rays and are therefore ideal for use in outdoor locations. It can also be used on gel-coat composites where there is a need for protection against severe weathering.

Suitable as an Anti-Graffiti coating

Defacement by, for example felt-tip pens is resisted by the surface and is simply “pearled-off”. More adhesive paints can be easily removed using common solvents (e.g. Acetone), or Nanolia Graffiti Remover liquid or gel, leaving no trace. Protected surfaces can be cleaned many times over and then simply recoated.

.

Technical Data:
Quantity of Product Required: 12g/m² – 30g/m²
Coating thickness: 3 – 10 µm (dry)
Dilution: Do not dilute
Color: Transparent, no gloss
Temperature Stability: -20 °C to +150 °C
Pot-Life: 15 – 30 minutes, keep bottles closed !
Dust Dry: After about 1 hour (at 20 °C)
Finally Dry: After about 2 -3 days (at 20 °C)
Second Coat: Not necessary
HVLP: Nozzle 0,8 mm. Pressure 2,0 bar

 

 

Always test a small sample to ensure that the desired result is achieved before proceeding with the main project. If in doubt, do not proceed.

Apply at a temperature between +5 °C and +40 °C. Avoid direct sunlight. The surface should be cleaned (free from fats, polishes, waxes and surfactants), dry and free from dust and any fatty/oily materials. The base surface to be treated must be thoroughly cleaned, dry and free from fat/oil, and also free of any silicone, wax or polish traces using Nanolia PreCleaner. Pre-treatment with Acetone is not sufficient. For Aluminium and Magnesium surfaces Nanolia Pre-Clean M1 is recommended..

Application is possible using the accepted methods (rolling, brush-painting, spraying or by immersion). To achieve the most successful surface HVLP Spray application is recommended. It can be applied alternatively with a roller or a lint-free cloth. Irregularities and striping of the surface can be corrected by the use of a PU-foam roller (using high pressure on the roller).

Please note that only a minimum surface thickness is needed !

Opened containers should be immediately closed/sealed. Should the contents, by the action of the atmosphere, become gelled, then the product is no longer able to be used.

After use, all utensils may be cleaned using normally available thinners. Details in application vary depending upon the surface to be coated. We are happy to advise you fully in these cases.

Depending entirely upon the surface to be treated, and the method used, about 50 – 60m² can be treated with one litre of this product.
1,0 litre bottle, 5 litre canister, 20 litre canister. Other packing forms/sizes are possible after prior consultation with us and according to the transport possibilities/regulations.
The product may be stored for at least 12 months in its original packing. Protect from frost and direct sunlight.

Empty containers as well as any remaining product must be disposed of according to the local laws and regulations or it must be taken to the community collection point for such materials.

When using this product please take note of these instructions. We wish to make it clear that the use of chemical preparations should only take place when the safety measures are observed and are always out of the reach of children. The technical information given here is according to the latest technical knowledge and composed from our own experience. In view of the many uses possible with this product it is the responsibility of the user to act according to the given situation in respect of safety – that is to say the user acts upon their own responsibility in any given situation when using this product. That the use of this product takes place out of our jurisdiction, we have set out safety and protection measures, but we cannot be held responsible in any circumstances. For any misuse of the product we cannot be held responsible. In the event of a new version of this information becoming available – this information here set out is no longer valid.
Nanolia Powercoat is not suitable for long term immersion in water. On white surfaces a slighty yellowing may occur due to strong UV exposure.